Power management and generator control

Paralleling GENSYS COMPACT PRIME

GENSYS COMPACT PRIME

New paralleling product with integrated programmation

GENSYS COMPACT PRIME

The GENSYS COMPACT PRIME is one controller of a complete range for Energy sources and power plant management : Generators, Mains, Photovoltaic, Batteries storage, Tie breakers. This controller is dedicated for generators used in power plant applications requiring synchronizing, active and reactive load sharing and electrical/mechanical protections. It offers flexibility and time saving thanks to its simple wiring, and easy programming.

Hardware & Display
The GENSYS COMPACT PRIME is available in both switchboard panel mounted version with display, or core base mounted version. And compatible with i4Gen touchscreen color display.
 
Software
The GENSYS COMPACT PRIME is configurable from its front panel display, from i4Gen remote touchscreen, or through the free i4Gen Suite software.
 
Control and Management
  • Compatible with 3 or 4 wires three-phase, or two-phase or single phase systems.
  • Up to 32 generators in parallel.
  • Complete engine control of diesel, gasoline or gas gensets (preheating, pre-glow, ignition, start/stop…).
  • 9 x Digital inputs: NO or NC to ground, 3 x Analog inputs: Resistive (0...500Ω) or 0...20mA,  6 x Digital outputs: NE or ND. 1.8A.
  • 31 calibration points for analogue inputs (resistive or 0-20 mA).
  • Expansion via CANopen: 32 x Digital inputs, 16 x Analog inputs, 32 x Digital outputs.
  • 2 x Relay outputs (breaker control): 5A, 240VAC.
  • 2 x Analog outputs: Speed/Frequency and Voltage control: +/-10VDC isolated output with adjustable span and offset.
  • Magnetic pick up input: Frequency from 50Hz...10kHz, Voltage 0.5...40VAC.
  • Alternative or consecutive multiple starter management.
  • Warmup & Cool down at idle or nominal speed.
  • Remote start and test mode available ON/OFF load.
  • Isochronous and Iso-voltage active & reactive load sharing.
  • Fixed kW/KVAR load or Droop mode.
  • Frequency and voltage control compensation for generators with droop governors and/or AVR/DVR.
  • Synchronization and dead bus management:
    • Static synchronization: gensets breakers closing without excitation.
    • Dynamic synchronization: Frequency, Phase and Voltage synchronization (Synch display available on screen). Synch check (ANSI 25) + Phase sequence protection. Phase shift between 0 and 360 degrees could be added on the synch check relay function (for example to compensate DYN11 MT/BT transformers).
  • New optimized PID loop with exceptional performance in synchronization, KW and KVAR control.
  • PATENTED SYSTEM, Easy Calib: Automatic control and automatic adjustment of analogue outputs speed and voltage.
    • Control of sufficient stability on the speed and voltage primary loops with alarm if applicable.
    • Control of a correction on speed and voltage with alarm if applicable.
    • Auto setting of nominal frequency, correct direction, and appropriate amplitude.
    • Auto setting of nominal voltage, correct direction, and appropriate amplitude.
    • Alarms information if the appropriate amplitude for speed or voltage is not reached.
  • Override mode (protections inhibition + dedicated hour meter) following NFE 37-312 certification.
  • Non-essential load trip on overload or overfrequency.
  • J1939:
    • Compatible with all J1939 electronic engines. 
    • Engine ECU address automatic detection.
    • « Sniffer/Spy » function to analyse the CAN frames.
    • Start/Stop control, speed, 50/60Hz selection.
    • 10 « custom » frames can be configured in writing and reading.
    • ECU support TIER 4 Final and Stage 5 with DPF and SCR management.
  • Record of 500 events/alarms/faults with timestamps. Displayed on controller screen and i4Gen with advanced filter.
  • 1350 logged events with timestamp and real-time value available, non volatile memory. Available on uploaded file. 
  • Master/Slave automatic redundancy.
  • Alternative selection, Drag and Drop system: 16 parameters can switch between 2 values..
  • Scheduler: daily, weekly, monthly. 10 configurables events.
  • Easyflex®, Drag and Drop system: 50 programming lines.
  • New Debug mode displaying in real time the status or value of all variables in the programming lines.
  • Easy connect: This function permit to quickly switch the connection between controllers.
    • Automatically detects CRE TECHNOLOGY controllers on an Ethernet network.
    • It allows to automatically configure CRE TECHNOLOGY controllers IP address to be able to access them with the current network configuration. 
  • Circuit breakers management:
    • The breakers positions feedback could be connected or not.
    • Adjustable pulses or latched contact for breaker closing.
    • Adjustable pulses or latched contact for breaker opening.
    • MN/MX coil management.
    • Closing failure, opening failure, unexpected closure, unexpected opening alarm management. 
  • New Modbus TCP Slave/Master Communication Port.
    • Modbus TCP Slave: All data are accessible by ModBus TCP locally or remotely (web, GPRS).
    • New Modbus TCP Master: possibility to create and configure customized frames
  • 3 isolated com ports are available:
    • 1 CANbus: J1939 electronic engine and I/O extensions.
    • 1 CANbus CRE protocol for communication between all COMPACT controllers.
    • Ethernet: PC communication/ModBus TCP.
  • Remote Supervision with color touch screen i4Gen. (7, 10 or 15 inches)
    • Sending emails to events.
    • 1 single I4Gen can monitor the entire power plant.
    • New Monitoring and control of the complete power plant (generators, mains, photovoltaic, batteries storage,..) through a single line diagram generated automatically.
    • Use of the Zoho Assist app (PC, MAC, Smartphone).
    • Up to 10,000 power plant with a single Zoho Assist account (Zoho Assist PC, MAC, Smartphone application).
    • Visualization - configuration - programming - remote power plant control.
    • Internet connection: Wan port or Wifi hotspot or 4G modem or Smartphone Access point.
  • Battery Boost management.
  • Configurable maintenance cycle.
  • Electrical and mechanical protections.
  • 3 password levels: end user, technician, advanced technician.
  • Languages: English, French, Italian, Spanish in standard. Portuguese, Russian, German and other custom languages are available on request.
  • Automatic clock synchronization by CANbus.
  • Automatic firmware update: When module is connected to i4Gen Suite PC software, you will automatically be asked for a firmware update to the latest version if applicable.

 

Add to cart In stock


File(s)



Associated Product(s)

Back to the list

Need a quotation ?

Ask for quotation